
All right, folks. This is short number 24 in our series on headstock breaks. If you haven't seen the first four, go to our channel and check them out. Okay, so we have Tomo Fujita's 61 custom shop SG Les Paul with a pig head crack, and I've got it all set up in the neck jig and clamped up, ready to go. But there's no glue in this. So let me take it all back
Машинный перевод (local:quickmt-en-ru+g1). Оригинал
Материал на языке оригинала: English.
Этот Gibson нуждается в инъекции! 💉
13 ноября 2026 г. · Источник: StewMac (YouTube)
Ладно, пора склеить эту штуку! В этом эпизоде я наконец-то занялся склеиванием треснувшего головного убора Tomo Fujita Gibson SG. Чтобы все было выстроено и надежно зажато, нужно немного планирования, и у меня есть несколько трюков в рукаве, чтобы помочь сделать работу правильно. Мы на шаг ближе к возвращению этой гитары в игровую форму! — - — - У StewMac есть все, что вам нужно для ремонта, создания или поддержания ваших гитар. Все, что мы продаем, поддерживается нашей жизнью.
Расшифровка видеоавто-субтитры · EN · RU
Нажмите на таймкод, чтобы перейти к моменту в видео
All right, folks. This is short number 24 in our series on headstock breaks. If you haven't seen the first four, go to our channel and check them out. Okay, so we have Tomo Fujita's 61 custom shop SG Les Paul with a pig head crack, and I've got it all set up in the neck jig and clamped up, ready to go. But there's no glue in this. So let me take it all back
All right, folks. This is short number 24 in our series on headstock breaks. If you haven't seen the first four, go to our channel and check them out. Okay, so we have Tomo Fujita's 61 custom shop SG Les Paul with a pig head crack, and I've got it all set up in the neck jig and clamped up, ready to go. But there's no glue in this. So let me take it all back
apart and show you what I've got planned. So we have this all set up at a pretty steep angle, and I'm hoping that that helps the glue flow into the crack instead of back out. But the bigger problem is that this crack is closed really tight. It's going to be tricky getting glue in here. So let me show you what I have planned. So the first part
apart and show you what I've got planned. So we have this all set up at a pretty steep angle, and I'm hoping that that helps the glue flow into the crack instead of back out. But the bigger problem is that this crack is closed really tight. It's going to be tricky getting glue in here. So let me show you what I have planned. So the first part
of my plan is to use this rubber band wrapped around the headstock and the neck jig to apply some pressure and force this crack open. But I have to be careful not to go too far or I risk busting this open even worse than it already is. So I have this jack under the headstock that will allow me to control the amount that it moves. But even best case scenario, I'm going to
of my plan is to use this rubber band wrapped around the headstock and the neck jig to apply some pressure and force this crack open. But I have to be careful not to go too far or I risk busting this open even worse than it already is. So I have this jack under the headstock that will allow me to control the amount that it moves. But even best case scenario, I'm going to
have a hard time getting glue all the way up in that crack. So I have another trick up my sleeve. Check this out. So a great way to get glue into really tight spaces is to inject it with a syringe. But tight bond is pretty thick. So by hand it can be hard to force it through a really thin needle. So I took this syringe and I adapted it to fit an air
have a hard time getting glue all the way up in that crack. So I have another trick up my sleeve. Check this out. So a great way to get glue into really tight spaces is to inject it with a syringe. But tight bond is pretty thick. So by hand it can be hard to force it through a really thin needle. So I took this syringe and I adapted it to fit an air
hose that goes into this airbrush compressor. Then I'm hooked to this foot pedal that I can use to start and stop this motor to pressurize this syringe and get glue to flow out this tiny little needle just like this. Pretty cool, right? Okay, I'm going to carefully pry this crack apart. I'm going to fill it full of glue until I see it coming out all along this crack.
hose that goes into this airbrush compressor. Then I'm hooked to this foot pedal that I can use to start and stop this motor to pressurize this syringe and get glue to flow out this tiny little needle just like this. Pretty cool, right? Okay, I'm going to carefully pry this crack apart. I'm going to fill it full of glue until I see it coming out all along this crack.
Then I'm going to clamp it together tightly and wrap it in rubber bands. Here we go. First, the rubber band that supplies the tension I need to open up this crack. That drives the headstock into the jack. So when I lower it into the beam, it forces the crack open until I can get a needle in there. Then I start injecting glue wherever I can slip
Then I'm going to clamp it together tightly and wrap it in rubber bands. Here we go. First, the rubber band that supplies the tension I need to open up this crack. That drives the headstock into the jack. So when I lower it into the beam, it forces the crack open until I can get a needle in there. Then I start injecting glue wherever I can slip
the needle in, being careful not to chip the finish or dislodge splinters that could prevent the crack from closing. I'm pushing way glue than I actually need in order to force it into the tight areas of the crack where the needle can't reach. When I release the rubber band tension, the crack relaxes and pushes out a lot of excess glue. I wiped
the needle in, being careful not to chip the finish or dislodge splinters that could prevent the crack from closing. I'm pushing way glue than I actually need in order to force it into the tight areas of the crack where the needle can't reach. When I release the rubber band tension, the crack relaxes and pushes out a lot of excess glue. I wiped
that away then screwed the jack back into the headstock forcing the crack closed squeezing out even more glue. I realized last minute that I needed to add more clamps to get the ends closed. Then I added a rubber band to ensure the edges of the crack closed flush. Okay, all in all I think that went well, but I wasn't anticipating needing those two
that away then screwed the jack back into the headstock forcing the crack closed squeezing out even more glue. I realized last minute that I needed to add more clamps to get the ends closed. Then I added a rubber band to ensure the edges of the crack closed flush. Okay, all in all I think that went well, but I wasn't anticipating needing those two
extra clamps. So that took a little longer than I thought. So I'm glad I used Titebond. If I'd used hot hide glue, I'd be a little worried right now that it started to thicken up before I really got it clamped all the way. So I think I made the right call there. I'm going to let this sit in clamps at least overnight then we'll take it out and see
extra clamps. So that took a little longer than I thought. So I'm glad I used Titebond. If I'd used hot hide glue, I'd be a little worried right now that it started to thicken up before I really got it clamped all the way. So I think I made the right call there. I'm going to let this sit in clamps at least overnight then we'll take it out and see
how we did then let it sit for another 24 hours before we decide what to do next. So thanks for joining us. We'll see you in the next one.
how we did then let it sit for another 24 hours before we decide what to do next. So thanks for joining us. We'll see you in the next one.
Ещё по теме
Инструменты, звук и мастераОстрые одетые гитары! Gibson Custom 1959 и США Билли Гиббонс Перли ГейтсAndertons Music Co (YouTube)
Инструменты, звук и мастераВнутренняя история новой фирменной гитары Джоша ХоммаGuitar.com
Инструменты, звук и мастераЕе оригинальный состав на редкой стальной строчке 😍🎸SiccasGuitars (YouTube)
Инструменты, звук и мастераGibson Билли Гиббонс Перли Гейтс Лес Пол: $20k Murphy Lab & USA StandardGibson анонсировала два Билли Гиббонса Перли Гейтса Les Pauls. Высококлассная версия за $20k и стандартная модель США The post Gibson Билли Гиббонс Перли Гейтс Лес Полс: $20k Murphy Lab & USA Standard появились первыми на gearnews.com.gearnews.com